3929539 Festo Positioners
Part#:3929539
Manufacturer:Festo
Category:Positioners
Alt. Part#:CMSX-P-SE-C-U-F1-D-130-A
Product Lifecycle:Active
Get a quick Quote!
positioner CMSX-P-SE-C-U-F1-D-130-A electropneumatic, for double-acting pneumatic quarter turn actuators, connection for external displacement/angle sensor, standard nominal flow rate 130 l/min, opening/closing regulating action safety position, 4-wire, p
About the manufacturer: Festo is one of the manufacturers that offers Positioners that you can order at Powermatic Associates site. Festo Corp. has been a top supplier of automation and intelligent automation solutions for more than four decades in the United States and eight decades globally. The company is committed to transforming the manufacturing sector and enhancing business efficiency.
Check out the 3929539 Festo price in the box on the right side or send a quick quote.
Product Details
- Shaft material High-alloy stainless steel
- Analog inputs, resolution 16 bit
- Vibration resistance Transport application test with severity level 2 as per FN 942017-4 and EN 60068-2-6 as per EN 60068-2-6
- Analog outputs, galvanic isolation no
- Switching output 3 x PNP or 3 x NPN switchable
- Digital outputs, short circuit current rating yes
- Analog outputs, short-circuit protection yes
- Analog outputs, overload protection yes
- Design digital, electropneumatic positioner
- Analog outputs, resolution 12 bit
- Contamination level 3
- Electrical connection 2, connection type Terminal strip
- Analog inputs, signal range 0 - 10 V 4 - 20 mA
- Analog outputs, reverse polarity protection yes
- Analog outputs, linearity error at 25°C 0.5%
- Digital inputs, reverse polarity protection yes
- Input characteristics As per IEC 61131-2, type 3
- Analog inputs, temperature coefficient < 0.02 %FS/K
- Analog outputs, max. load resistance ≤ 600 Ohm
- Reverse polarity protection for operating voltage connections
- Measuring principle of linear potentiometer Potentiometer
- Connection resistance ≤ 80 kOhm
- Information on operating and pilot media Operation with oil lubrication not possible
- Material for cable connector PA
- Analog inputs, overload protection yes
- Analog inputs, galvanic isolation no
- Quick-coupling material High-alloy stainless steel
- Electrical connection 2, function External path/angle sensor
- Electrical connection 1, connection type Terminal strip
- Mode of operation Double-acting
- Inspection window material PC
- Electrical connection 1, function 2x digital input Load power supply
- Analog outputs, temperature coefficient < 0.02 %FS/K
- Nominal operating voltage DC 24 V
- Type code CMSX
- Operating pressure 3 bar ... 8 bar
- Certification RCM compliance mark
- Cable fitting M12 x 1.5 for electrical connection 2 M20 x 1.5 for electrical connection 1
- Standard nominal flow rate 130 l/min
- Housing material PC-reinforced
- Storage temperature -20 °C ... 60 °C
- Digital inputs, electrical isolation Yes, optocoupler
- Digital outputs, output current 100 mA
- Display 7-segment With backlighting
- Mounting position Any
- Electrical connection 1, connection technology Screw terminal
- Max. cable length 3 m for electrical connection 2 30 m for electrical connection 1
- Dimensions W x L x H 190 mm x 105 mm x 130 mm
- Analog outputs, signal range 4 - 20 mA
- Electrical connection 1, tightening torque 0.6 Nm
- Electrical connection 1, conductor cross section < 1.5 mm²
- Size of dead space 0.5 % ... 10 %
- Degree of protection IP65
- Type of mounting With accessories
- Seals material NBR
- Material of screws High-alloy stainless steel
- Approved cable diameter 7-13 mm for electrical connection 1 3-6.5 mm for electrical connection 2
- Switching input PNP NPN
- Relative air humidity 93 %
- Digital outputs, potential separation Yes, optocoupler
- Analog inputs, linearity error at 25°C 0.5%
- Digital outputs, reverse polarity protection yes
- Electrical connection 2, connection technology Screw terminal
- Digital outputs, overload protection yes
- Electrical connection 2, number of pins/wires 2
- Electrical connection 2, tightening torque 0.6 Nm
- Electrical connection 2, conductor cross section < 1.5 mm²
- DC operating voltage range 21.6 V ... 26.4 V
- CE marking (see declaration of conformity) As per EU EMC directive As per EU RoHS directive
- Pneumatic connection G1/8
- Note on materials RoHS-compliant
- Shock resistance Shock test with severity level 1 as per FN 942017-5 and EN 60068-2-27 as per EN 60068-2-29
- Base plate material Wrought aluminum alloy Anodized
- Max. current consumption 600 mA
- Electrical connection 1, number of pins/wires 14
- Setting options Via display and pushbuttons
- Operating medium Compressed air as per ISO 8573-1:2010 [7:4:4]
- Ambient temperature -5 °C ... 60 °C
- Product weight 970 g
Product condition
New Factory Sealed
New Factory Sealed - New condition, never used, original OEM part with original packaging and factory seal.
Related documents 3929539 Specs
Manufacturer warranty
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
Worldwide Shipping and Delivery
Secure Payment Processing
Warranty
Responsive Customer Support
Got Questions? We've Got Answers!
Need more details?
Feel free to chat with us
Relevant products
What can I help you find today?
