8069728 Festo Pneumatic Components

Product Details

• IP address allocation
  FCT DCP
• Baud rate
  10/100 Mbit/s (full/half)
• Rotor position sensor measuring principle
  Magnetic
• Nominal rotary speed
  3150 1/min
• Max. negative test pulse on 1 signal
  600 µs
• DC nominal voltage
  24 V
• Nominal current
  7.2 A
• Media redundancy
  MRP
• Rotor position sensor
  Absolute encoder, multi-turn
• Safety integrity level (SIL)
  Safe torque off (STO)/SIL 2
• Braking resistor, external
  6 Ohm
• Hardware fault tolerance
  1
• Parameterization interface
  Ethernet
• Peak current
  10.3 A
• Vibration resistance
  Transport application test with severity level 2 as per FN 942017-4 and EN 60068-2-6
• Ambient temperature
  0 °C ... 50 °C
• Peak torque
  0.91 Nm
• Number of digital logic outputs 24 V DC
  2
• Characteristics of logic input
  Galvanically connected to logic potential
• Switching logic at outputs
  PNP (positive switching)
Safety function
Safe torque off (STO)
Display
LED
Max. positive test pulse with 0 signal
10000 µs
SFF safe failure fraction
> 90 %
Rotor position sensor resolution
12 bit
Certificate issuing authority
German Technical Control Board (TÜV) 01/205/5514.00/16 UL E331130
Shock resistance
Shock test with severity level 2 as per FN 942017-5 and EN 60068-2-27
KC characters
KC EMC
Configuration support
GSDML file
Controller operating mode
PWM MOSFET power output stage PI current regulator
Protective function
I²t monitoring Software end position detection
Max. rotational speed
3300 1/min
Max. current of digital logic outputs
100 mA
Motor nominal power
150 W
Max. number of positioning sets
64
Additional functions
Conformance class B SNMP
Topologies
Star Line
Minimum cycle time
2 ms
Type code
EMCA
Performance Level (PL)
Safe torque off (STO)/category 3, performance level d
Diagnostic coverage
90 %
Characteristics of digital logic outputs
Freely configurable in some cases Not galvanically isolated
Protocol
PROFINET
Permissible voltage fluctuations
+/- 20 %
Storage temperature
-25 °C ... 70 °C
Certification
RCM compliance mark c UL us - Recognized (OL)
Rotor mass moment of inertia
0.301 kgcm²
Permissible axial shaft load
60 N
Work range of logic input
24 V
Input switching logic
PNP (positive switching)
Absolute encoder operating time
With external battery: max. 6 months Note: the maximum service life of the battery depends its state of charge, the ambient temperature and ageing effects. Without external battery: 3 days (worst case) up to a maximum of 7 days (best case) Note: Maximum s
CE marking (see declaration of conformity)
As per EU EMC directive as per EU machinery directive
Note on ambient temperature
Above an ambient temperature of 20 °C, the power must be reduced by 1.75% per °C.
PFH
1.0E-9
Product weight
2285 g
Logic input specification
Based on IEC 61131-2
Note on materials
Contains paint-wetting impairment substances RoHS-compliant
Motor peak power
200 W
Relative air humidity
0 - 95 % Non-condensing
Degree of protection
IP54
PFD
1.86E-5
Number of digital logic inputs
2
Communication profile
FHPP
Type of mounting
Screwed tightly With through-hole
Nominal torque
0.45 Nm
Permissible radial shaft load
100 N
Proof test interval
20 y
Ethernet, supported protocols
TCP/IP

Related documents 8069728 Specs