8133357 Festo Servo Amplifiers

Product Details

• KC characters
  KC EMC
• Fieldbus interface, connection technology
  RJ45
• Encoder interface 2, function
  Incremental encoder SIN/COS encoder
• Number of inputs for motor temperature sensor
  1
• Max. current of the floating switching outputs
  50 mA
• Number of diagnostic outputs
  2
• Max. short circuit protection of mains
  10 kA
• Max. voltage drop from logic supply to brake output
  1 V
• Time resolution of high-speed switching outputs
  1 µs
• Safety integrity level (SIL)
  Safe brake control (SBC)/SIL 3/SILCL 3 Safe torque off (STO)/SIL 3/SILCL 3
• Braking resistor, external
  40 Ohm ... 60 Ohm
• Hardware fault tolerance
  1
• Pulse power of braking resistor
  13.6 kVA
• Controller nominal power
  6000 VA
• SFF safe failure fraction
  99 %
• Max. current consumption for logic supply with clamping brake and I/O
  2.5 A
• CE marking (see declaration of conformity)
  As per EU EMC directive As per EU RoHS directive
• Relative air humidity
  5 - 90 % Non-condensing
• Certification
  RCM compliance mark c UL us - Listed (OL)
• Communication profile
  DriveProfile
Logic input specification
Based on IEC 61131-2, type 3
Fieldbus coupling
EtherNet/IP
Fieldbus interface, transmission rate
100 Mbit/s
Encoder interface, function
EnDat® 2.1 encoder SIN/COS encoder
Synchronization interface, function
Encoder emulation A/B/Z Encoder input A/B/Z
Number of high-speed logic inputs
2
Braking resistor nominal power (IEC)
100 W
Max. current consumption for logic supply with parking brake
2 A
Controller operating mode
Cascade control Autotuning
Performance Level (PL)
Safe brake control (SBC)/category 3, performance level e Safe torque off (STO)/category 4, performance level e
Display
LED green/yellow/red
Diagnostic coverage
97 %
Impedance of setpoint input
70 kOhm
Nominal operating voltage AC
400 V
Max. DC link voltage
800 V
Mains frequency
48 Hz ... 62 Hz
Peak current, load supply
45 A
Max. current consumption for logic supply without clamping brake
0.5 A
Load supply permissible range
± 10 %
Permissible voltage fluctuations
+/- 10 %
Degree of protection
IP20
Number of analog setpoint inputs
1
Number of digital logic outputs 24 V DC
6
Encoder interface output, characteristics
1 MHz maximum output frequency max. 16384 ppr
Switching logic at outputs
PNP (positive switching)
Type code
CMMT-AS
Information on max. installation height
1% power reduction/100 m above 1000 m.
Protection class
I
Overvoltage category
III
Number of floating switching outputs
1
Max. output current of holding brake
1.5 A
Max. installation height
2000 m
Active PFC
no
Safety function
Safe brake control (SBC) Safe stop 1 (SS1)
Braking resistor, integrated
47 Ohm
Max. length of motor cable without ext. mains filter
25 m
Input voltage range AC
200 V ... 480 V
Nominal voltage, logic supply DC
24 V
Nominal current load supply
15 A
Surge resistance
6 kV
Permissible range of logic voltage
± 20 %
Note on ambient temperature
Above an ambient temperature of 40 °C, the power must be reduced by 3%/°C.
Work range of logic input
-3 V ... 30 V
Encoder interface input, characteristics
1 MHz maximum output frequency max. 16384 ppr
Input switching logic
PNP (positive switching)
Type of mounting
Mounting plate, screwed on
Mounting position
Free convection Vertical
Ethernet interface, protocol
TCP/IP
Mains types
TN IT
Number of high-speed switching outputs
2
System voltage to EN 61800-5-1
300 V
Number of safe 2-pin inputs
2
Conforms to standard
EN 61800-3 EN ISO 13849-1
Line filter
Integrated
Output frequency
0 Hz ... 599 Hz
Max. peak current duration
2 s
Nominal current per phase, effective
12 A
Peak power
18000 VA
Ambient temperature
0 °C ... 50 °C
Product weight
4100 g
Process interfacing
Adjustable-Speed Drives Drives with positioning function
Operating range of analog inputs
± 10 V
Characteristics of setpoint inputs
Differential inputs Configurable for current/force
Note on materials
Contains paint-wetting impairment substances RoHS-compliant
Fieldbus interface, function
Bus connection, incoming/forwarding EtherNet/IP slave
Ethernet interface, function
Parameterization and commissioning
Fieldbus interface, protocol
EtherNet/IP
Fieldbus interface, connection type
2x socket
Max. continuous output of the external braking resistor (IEC)
3000 W
Pulse energy for braking resistor
1200 Ws
Time resolution of high-speed logic inputs
1 µs
Based on norm
EN 50581 EN 62061
Mode of operation
Field-oriented regulation 1x SYNC interface for encoder emulation or encoder input
Control elements
Optional: CDSB operating unit
Output voltage range AC
3x (0 – input) V
Characteristics of digital logic outputs
Freely configurable in some cases Diagnostic outputs in some cases
Max. current of digital logic outputs
20 mA
Nominal voltage, load supply DC
560 V
Nominal operating voltage phases
3-phase
Peak current per phase, effective
36 A
Contamination level
2
Certificate issuing authority
German Technical Control Board (TÜV) Rheinland 01/205/5640.00/18 UL E331130
Storage temperature
-25 °C ... 55 °C
UL-ambient temperature
0 °C ... 40 °C
Number of digital logic inputs
12
Work range of setpoint input
± 10 V
Characteristics of logic input
Freely configurable in some cases Not galvanically isolated

Related documents 8133357 Specs